#Cateye enduro 8 wheel size free#

Select any mode except ODO, then press M button and S/S button si- multaneously.

In TM, DST or AVS mode - On/off the Auto function.

When pressed in stop state in each mode, the following can be revised. This is for setting the wheel circumference and clock time, switching on/ off Auto Function and to clear all present data and any irregularity. In Auto Function, this button is invalid. During operation, speed scale symbol flashes. Starts and stops the measurement of trip distance and elapsed time. *If held over 2 seconds, 12-hour clock appears. 1, and data is displayed on the sub-display. By pressing M button or S/S button, or by receiving signal, this function is released.Ĭhanges the display in the order shown in fig. When main unit is left without receiving any signal for 60-70 minutes continu- ously, power supply is shut down and main unit will display (įigure. The specifications and design are subject to change without notice.Ī. 3 years(The life of the first factory-loaded battery may be shorter than this period.)ġ-15/16' x 1-25/32' x 5/8' (49 x 45 x 16 mm) / 0.74 oz (21 g) Softly wash away such objects with water.Īpprox.

If there is mud, sand or the like clogs between the button and the body, the movement of theīutton may be disturbed.

Paint thinner, benzine, or alcohol, to avoid damages on the surface.

For cleaning, use neutral detergent on soft cloth, and wipe off later with dry cloth.

Check relative position of sensor and magnet periodically.

Road and duly consider to traffic safety.

Don't pay too much attention to your computer's functions while riding! Keep your eyes on the.

Do not disassemble the main unit, sensor and magnet.

Do not leave the main unit exposed to direct sunlight when the unit is not in use.

Is the unit in the Auto function? - The S/S button doesn't function in the Auto function.

When the S/S button is pressed, the unit doesn't activate or stop. Do not use industrial water repellent it may damage the bracket. Contacts can also be treated with a water repellent silicon jell from an automotive parts or hardware store.

Water or condensation may collect between the bracket sensor and the computer causing an Contacts on the bracket might not be repelling wets efficiently. Transmission signal loss in damp or wet conditions. Is the wire broken? - Replace the Bracket & Sensor part with a new one. Is the distance between sensor and magnet too far? - Are the marking line of the sensor and the center of magnet matched each other? - Refer to 'Sensor/Magnet Mounting' and re-adjust correctly. Is there anything on the contact of the main unit or of the bracket? - Wipe the contact clean. Has the Lithium Battery in the main unit worn out? - Replace the Lithium Battery with a new one. It returns to normal state when temperature rises. The unit will function normally if the speed display appears. When current speed does not appear, short-circuit the contact on the back with metal. Check the following before taking to repair. The following situations do not indicate malfunction of the cyclocomputer. * 2 seconds may be elapsed if mount the main unit to the bracket with this func. *With this function, it ceases measuring elapsed time during a stop. In TM, DST or AVS, this function switches on/off with each press of SET button.

#Cateye enduro 8 wheel size free#

This function switches the main unit to start or stop automatically, in which AUTO symbol appears on the screen, and you are free from pressing S/S button each time. The current time is displayed by a 12-hour clock. With Reset operation, it returns to zero and counting begins anew. If either is ex- ceeded, (.E) is displayed and calculation ceases. The average speed from start to current point is displayed within 27 hours 46 minutes 39 seconds (99,999 seconds) or 999.99 miles (km). With Reset operation, it returns to zero. At 10 hours, it returns to zero and counting begins anew. With Reset operation, it returns to zero.Įlapsed time is measured from start to current point, in units of hours, minutes and seconds. The trip distance from start to current point is displayed. At 10,000 miles(km), it returns to zero and counting begins anew. This is continuously measured until battery wears down or all clear operation is done. This is always displayed on the main display and updated once a second.